View RCL175PS12_4494064.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AC-DC
175 Watts RCL175 Series
* * * * * * * 200 W Peak Rating
xppower.com
Up to 120 W Convection-cooled Industrial and Medical Approvals Low Leakage Current Class I & Class II Applications Flexible Design for Modified Standards Connector & Mechanical Options
Specification
Input
* 85-264 VAC (120-370 VDC) See note 3 * 47-63 Hz * 2.1 A max at 115 VAC 0.9 A max at 230 VAC Inrush Current * 17 A max at 115 VAC, 35 A max at 230 VAC, cold start at +25 C Power Factor * Complies with EN61000-3-2 for Class A equipment Earth Leakage Current * 120 A max at 115 VAC 200 A max at 230 VAC Input Protection * 3.15 A line and neutral fused Input Voltage Input Frequency Input Current
General
Efficiency Isolation * 80-90% depending on model * 4000 VAC Input to Output 1500 VAC Input to Ground 1500 VAC Output to Ground open frame (For BF applications, consult sales office) 500 VAC Output to Ground U channel & covered * PFC 75 kHz typical, PWM 60 kHz typical * Power fail - open collector output referenced to 0 V sense * See Application Notes * See Application Notes * 385 kHrs typical at +25 C per MIL-HDBK-217F
Switching Frequency Signals Remote Sense Remote On/Off MTBF
Output
* See models and ratings table * 10% output 1 via pot, outputs 2-4 track by same percentage Initial Set Accuracy * 2% of nominal at 50% load Minimum Load * See models & ratings table Start Up Delay * <2 s Start Up Rise Time * <100 ms Hold Up Time * 20 ms min at nominal low line & maximum power Drift * <0.2% after 20 mins warm up Line Regulation * 0.5% of nominal over full input range Load Regulation * PQ42 & 43: V1 & V2 3%, V3 & V4 5% of nominal, all other models: V1 1%, V2, V3 & V4 5% of nominal Transient Response * 4% max deviation, recovery to within 1% in 500 s for a 25% load change at 1 A/s Ripple & Noise * 50 mV (Vo=<5 V), 120mV (Vo=12, 15 V), 200 mV (Vo=24, 48 V). Measured pk-pk with a 20 MHz bandwidth Overvoltage Protection * 115-140% - V1 only. Cycle mains to reset Overtemperature * Fitted with auto restart Protection Overload Protection * 110-125% - Primary side power limiting with auto recovery. Constant current limit for single output models and foldback current limit for multi output models. V3 & V4 PTC resetting fuses Temperature * 0.02%/C Coefficient Output Voltage Output Voltage Trim
Environmental
Operating Temperature * -10 C to +50 C at full power, derate to 50% power at +70 C Operating Humidity * 5-95% RH, non-condensing Storage Temperature * -20 C to +85 C Operating Altitude * 3000m Shock * 30 g peak, half sine, 6 axes Vibration * 2 g rms, 5-500 Hz, 3 axes
EMC & Safety
Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions * EN55011/22 class B conducted, class A radiated * EN61000-3-2 for class A equipment * EN61000-3-3 * EN61000-4-2, Level 3 Perf Criteria A * EN61000-4-3, 10 V rms 80% mod, Perf Criteria A * EN61000-4-4, Level 3 Perf Criteria A * EN61000-4-5, Level 3 Perf Criteria A * EN61000-4-6, Level 3 Perf Criteria A * EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B * EN60601-1-1, EN60950-1:2001, UL/cUL60950:2003, CSA60601.1, UL60601-1:2003.
Safety Approvals
AC-DC
Models and Ratings
Total Power Max(7) 175 W 175 W 175 W 175 W 175 W 175 W 175 W 175 W 175 W 175 W 175 W 175 W 175 W Peak Conv.(4,5) 204 W 195 W 200 W 200 W 202 W 200 W 200 W 200 W 200 W 200 W 200 W 200 W 200 W V 120 W 12.0 V 120 W 15.0 V 120 W 24.0 V 120 W 28.0 V 120 W 48.0 V 110 W 110 W 110 W 90 W 90 W 90 W 90 W 90 W 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V Output 1 Min 0.0 A 0.0 A 0.0 A 0.0 A 0.0 A 1.5 A 1.5 A 1.5 A 1.5 A 1.5 A 1.5 A 1.5 A 1.5 A Max Peak(1) V 14.5 A 17.0 A 11.6 A 13.0 A 7.2 A 6.2 A 3.6 A 15.0 A 15.0 A 15.0 A 15.0 A 15.0 A 15.0 A 15.0 A 15.0 A 8.3 A 7.1 A 4.2 A 12.0 V 12.0 V 15.0 V 3.3 V 12.0 V 15.0 V 24.0 V 24.0 V 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 8.3 A 6.3 A 4.6 A 15.0 A 5.5 A 4.0 A 3.2 A 3.0 A 10.4 A 8.4 A 6.6 A 7.6 A 6.0 A 5.0 A 5.0 A F 12 V F 15 V F 15 V F5V F5V F 12 V F 15 V 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 2.0 A 2.0 A 2.0 A 2.0 A 2.0 A 2.0 A 2.0 A F 15 V F 12 V F 15 V F 12 V F 15 V Output 2(6) Min Max Peak(1) V Output 3(6,8) Min Max V Min
RCL175
Output 4(6,8) Max Model Number RCL175PS12 RCL175PS15 RCL175PS24 RCL175PS28 RCL175PS48 RCL175PD22(4,6) RCL175PT31(4,6) RCL175PT32(4,6) 0.1 A 0.1 A 0.1 A 0.1 A 0.1 A 2.0 A 2.0 A 2.0 A 2.0 A 2.0 A RCL175PQ43(5,6) RCL175PQ44(6) RCL175PQ45(4,6) RCL175PQ46(4,6) RCL175PQ47(4,6)
Notes
1. Peak rating can be taken for 5 seconds in every minute. Average power not to exceed maximum power. 2. There is a user-accessible fan supply rated at 12 V at 350 mA (not available on fan-cooled units). 3. For operation at 85 VAC output power is derated to 95%. 4. Output 1 10 A max convection-cooled. 5. 20 A max from output 1 and 2 combined convection-cooled. 6. A minimum load of 100 mA is required on output 2, 3 and 4 to maintain the regulation figures. 7. 12 CFM airflow required for maximum power. 8. Outputs 3 & 4 are floating, they can be connected externally for positive or negative output. 9. Connector kits and cable harnesses available. Consult sales for options.
Pin Connectors
Pin 1 2 3 INPUT CONNECTOR - P1 Function Live N/C Neutral
Application Notes
Remote Sense Power Fail Remote On/Off V1 only, compensates for 0.5 V or 10% whichever is lower. Open collector output refers to 0 V sense (when using the power fail signal, -Sense must be connected to 0 V). Connect pin 1 (P3) to 0 V to disable unit (optional remote enable specify suffix `-E' with the model number). Applying a logic `0' will also disable the unit.
P1 is a 3-way 0.156" pitch square pin header Molex housing 09-91-0300 pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) OUTPUT CONNECTOR - P2 Function +Output 1 +Output 1 +Output 1 0V 0V 0V 0V 0V 0V +Output 2 +Output 2 +Output 2 -Output 3 +Output 3 -Output 4 +Output 4 SIGNALS CONNECTOR - P3 Function Remote On/Off +Sense -Sense PF signal 0 V fan supply +12 V fan supply
Options
* For the U-channel version, add suffix `-U' to the model number. * For the U-channel version with cover kit, add suffix `-C' to the model number. * For the U-channel version with fan cover kit, add suffix `-F' to the model number. * For screw terminals (output connector P2 only), add suffix `-S' to the model number. * For versions with remote enable, contact sales. * For foldback current limit on single output models, contact sales. * For constant current limit (output 1 & 2) on multi-output models, contact sales.
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Connector Info
For all formats, output connector P2 as follows: Single Output Models: 6-way 0.156" pitch square pin header Molex housing 09-91-0600 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) Dual Output Models: 12-way 0.156" pitch square pin header Molex housing 09-91-1200 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) Triple Output Models: 14-way 0.156" pitch square pin header Molex housing 09-91-1400 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) Quad Output Models: 16-way 0.156" pitch square pin header Molex housing 09-91-1600 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG)
Pin 1 2 3 4 5 6
P3 is a 6-way 0.1" pitch square pin header Molex housing 22-01-2065 pins 08-50-0032
AC-DC
Mechanical Details
All dimensions are in inches (mm) Tolerance 0.02 (0.5) Open Frame Weight: 1.10 lbs (500 g) approx.
RCL175
5.50 (139.7)
Pin 16
3.70 (93.9)
3.26 (82.9)
1.28 (32.4)
0.14 (3.5) MOUNTING HOLE (4 POSITIONS)
Pin 6
P3
Pin 1
P2 P1
2
Pin 1
Earth/Safety Ground Tag (Class I Operation)
0.22 (5.5)
5.23 (132.7)
Note: 1. Suitable for class I and class II operation, for class II applications contact sales. 2. Overall height: 1.36 (34.6).
U-channel
5.71 145.0
Weight: 1.54 lbs (700 g) approx.
0.47 (12.0)
0.24 (6.2)
5.23 (132.7)
0.89 (22.5)
3.94 (100.0)
Pin 16
3.90 (99.0)
3.26 (82.8)
P2 P1
2
2.95 (75.0)
0.14 (3.5) MOUNTING HOLE (4 POSITIONS)
8-32 UNC MOUNTING HOLE (IN 4 POSITIONS)
M3 MOUNTING HOLE (IN 4 POSITIONS)
Pin 1
Earth/Safety Ground Tag 1.18 (30.0) 3.35 (85.0) M3 MOUNTING HOLE (IN 2 POSITIONS EACH SIDE) 0.55 (14.1) 4.60 (116.8)
1.50 (38.1)
0.74 (18.7)
1.60 (40.8)
2.50 (63.5)
8-32 UNC MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE)
Note: 1. Suitable for class I operation only. 2. Mounting screws must not penetrate by more than 0.12" (3.0 mm) max
0.08 (2.0)
AC-DC
Mechanical Details
All dimensions are in inches (mm) U-channel & Cover
5.71 (145.0) 0.24 (6.1) 5.23 (132.7) 0.89 (22.5)
RCL175
Weight: 1.76 lbs (800 g) approx.
Pin 16
3.90 (99.0)
3.26 (82.9)
P2 P1
2
2.95 (75.0)
0.14 (3.5) MOUNTING HOLE (4 POSITIONS)
0.47 (12.0)
3.94 (100.0)
8-32 UNC MOUNTING HOLE (IN 4 POSITIONS)
M3 MOUNTING HOLE (IN 4 POSITIONS )
Pin 1
Earth/Safety Ground Tag
M3 MOUNTING HOLE (IN 2 POSITIONS EACH SIDE)
1.18 (30.0)
3.35 (85.0)
0.55 (14.1)
4.60 (116.8)
Note: 1. Suitable for class I operation only. 2. Mounting screws must not penetrate by more than 0.12" (3.0 mm) max
1.60 (40.8) 2.50 (63.5) 8-32 UNC MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE)
1.59 (40.4)
U-channel & Fan Cover
5.71 (145.0)
0.74 (1.87)
Weight: 1.98 lbs (900 g) approx.
0.89 (22.5) 0.47 (12.0)
3.94 (100.0)
0.24 (6.1)
5.23 (132.7)
Pin 16
3.90 (99.0)
3.26 (82.9)
P2 P1
2
2.95 (75.0)
0.14 (3.5) MOUNTING HOLE (4 POSITIONS)
8-32 UNC MOUNTING HOLE (IN 4 POSITIONS)
M3 MOUNTING HOLE (IN 4 POSITIONS)
Pin 1
Earth/Safety Ground Tag 1.18 (30.0) 3.35 (85.0) M3 MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE) 2.14 (54.4) 4.60 (116.8)
0.55 (14.1)
Note: 1. Suitable for class I operation only. 2. Mounting screws must not penetrate by more than 0.12" (3.0 mm) max
1.60 (40.8) 2.50 (63.5) 8-32 UNC MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE)
1.57 (40.0)
0.74 (18.7)
03-Jul-08

▲Up To Search▲

Price & Availability of RCL175PS12

	To Download RCL175PS12 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .